BONFIGLIOLI act 401 Instrucciones de operaciones Pagina 61
- Pagina / 73
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
60 06/05
5.3 Digital output EM-S1OUTD
5.3.1 General
The digital output of the EM-IO-02 expansion module is desi
g
ned as a make contact
relay. Parameterization of this di
g
ital output permits a linkin
g
to a variety of functions.
The selection of functions depends on the parameterized configuration.
5.3.2 Operation modes
The operation mode of the digital output (Terminals X410A.6 and 7) is selected via the
parameter
Operation Mode EM-S1OUTD 533.
T
he operation modes to be selected correspond to the table shown in the operatin
g
instructions of the frequency inverter in the chapter "Digital outputs“.
5.4 Digital inputs EM-SxIND
The EM-IO-02 expansion module has three di
g
ital inputs. The assi
g
nment of the control
signals to the available software functions can be adapted to the application in ques-
tion. As a function of the selected
Configuration 30, the factory-set assi
g
nment and
the selection of the operation mode differ. In addition to the digital control inputs avail-
able, further internal logistic signals are also available as sources.
The individual software functions are assigned to the various signal sources via parame-
terization-capable inputs. This enables a flexible and varied use of the di
g
ital control
signals.
Operation mode Function
320 - EM-S1IND Signal on digital input 1 (X410A.3)
321 - EM-S2IND Signal on digital input 2 (X410A.4)
322 - EM-S3IND Signal on digital input 3 (X410A.5)
520 - EM-S1IND inverted Inverted signal on digital input 4 (X410A.3)
521 - EM-S2IND inverted Inverted signal on digital input 5 (X410A.4)
522 - EM-S3IND inverted Inverted signal on digital input 6 (X410B.5)
Alon
g
side the operation modes listed, those stated in the operatin
g
instructions of the
frequency inverter in the chapter "Digital inputs" also apply.
5.4.1 Fixed reference values and fixed value switch-over
Depending on the
Reference Frequency Source 475 selected, fixed frequencies can be
used as reference values. The EM-IO-02 expansion module extends the functionalit
y
described in the operating instructions of the frequency inverter (parameter
Fixed fre-
quency change-over 1
66 and Fixed frequency change-over 2 67) by the parameter
Fixed frequency change-over 3 131 and the matching parameters
F
ixed frequency 5
485, Fixed frequency 6 486, Fixed frequency 7 487, Fixed frequency 8 488.
F
ixed frequency
change-over 1
66
F
ixed frequency
change-over 2
67
F
ixed frequency
change-over 3
131
F
ixed frequency 1 480
0 0 0
F
ixed frequency 2 481
1 0 0
F
ixed frequency 3 482
1 1 0
F
ixed frequency 4 483
0 1 0
F
ixed frequency 5 485
0 1 1
F
ixed frequency 6 486
1 1 1
F
ixed frequency 7 487
1 0 1
F
ixed frequency 8 488
0 0 1
- Expansion module EM-IO-02 1
- 1.1 General information 6
- 1.2 Proper use 6
- 1.3 Transport and storage 7
- 1.5 Electrical connection 7
- 1.6 Operation information 7
- 1.7 Maintenance and service 7
- 2 Introduction 8
- 3.1 General 9
- 3.2 Mechanical installation 9
- 3.3 Electrical installation 11
- 3.3.1 Circuit diagram 11
- 3.3.2 Control terminals 12
- 4 System bus interface 13
- 4.1 Bus termination 13
- 4.2 Cables 14
- 4.3 Socket X410B 14
- 4.5 Setting node address 15
- 4.6 Functional overview 16
- 4.7 Network management 16
- 4.8 Master functionality 18
- Identifier 20
- SYNC-Time 919 20
- Inverter 1 22
- Inverter 2 Inverter 2 22
- System bus 22
- 4.9 Slave functionality 23
- 4.9.1.1 Boot-up message 23
- 4.9.1.2 Status control 23
- 4.9.2 Process SYNC telegram 24
- 4.9.4 Server SDO1/SDO2 26
- SDO2 Set Active 923 27
- 4.10.2.1 Profibus-DP 30
- 4.11.5 Virtual links 36
- 4.12 Control parameters 43
- 44 06/05 45
- 4.14 Utilities 46
- Load system bus 50
- Total load [%] 70 50
- 5.1 Analog input EM-S1INA 51
- 5.1.1 General 51
- Y +−⋅= 52
- 5.1.4.1 Examples 53
- Tolerance band 560 is not 54
- 5.1.5 Scaling 55
- 5.1.8 Adjustment 58
- 5.1.9 Filter time constant 58
- 5.2.1 General 59
- 5.2.2 Operation modes 59
- 5.2.3 Adjustment 59
- 5.2.4.1 Examples 60
- 5.3.1 General 61
- 5.3.2 Operation modes 61
- 5.4 Digital inputs EM-SxIND 61
- 5.5.1 Division marks 62
- 5.5.2 Actual speed source 63
- 5.7 Actual value display 64
- 5.9 Motor temperature 66
- Operation Mode 465 67
- 6 Parameter list 68
- 6.1 Actual value menu (VAL) 68
- 6.2 Parameter menu (PARA) 68
- % -100.00 ... 100.00 5.2.4 69
- 7 Annex 71
- 7.1 Error messages 71
- INDUSTRY PROCESS 73
- AND AUTOMATION SOLUTIONS 73
- COD. VEC 218 R0 73
Relacionado con productos y manuales para Adaptadores E Inversores De Energía BONFIGLIOLI act 401
(176 paginas)
(74 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales